Beach profiling Ella E.
Materials
emery rods (1)
Writing utensil (1)
Beach profiling sheet
(note sheet), (1)
Hammer (1)
Metal detector (1)
Laser Level
GPS
Camera (1)
Metal pole (1)
Monument (1)
A beach
More than one person
Methods
Go to a beach.
Find the wrack line. (Tide line)
Take your monument, and hammer it into
your fixed point. (Fixed point is the spot where you start.)
Take the longitude and latitude at
that spot with your GPS.
Stick a metal pole where the transect
line is. (A transect line is the path you are measuring)
Take out your emery rods. (Emery rods
are two poles with a taut rope tied in between)
Take one pole and Put it on the slope
(or flat land), and align with the horizon.
Take both poles and place them
opposite of each other.
Take the pole aligned with the
horizon, and look what that mark is on the pole opposite to it.
There will be numbers on the poles,
the mark will be one of these numbers. This is your data.
Do this until all the data needed to
find changes in the beach is collected.
Record or write down anything observed
in beach profiling note sheet.
Pick up after yourself, and leave the
beach cleaner and better than you found it!
Beach Profiling Samuel H.
Procedure
A.
Materials
·
Slope
·
Emory rods
·
Notebook and pencil
·
Hammer
·
Medal detector
·
More than one
person
·
A beach
·
Visible horizon
·
Data sheet
·
Camera
·
Metal pole
B. Methods
1.
Record the time, date,
longitude, latitude, and temperature.
2.
Use the hammer to hammer
the metal pole into you starting point (the dunes).
3.
Place one of the emery
rods next to metal pole, then bring the other pole as far away as you can.
(Make sure they're both straight up!)
4.
Have one of the
people be put behind the first rod and line up the horizon and the a marking on
the far rod.
5.
Measure and record what
number they both line up on. Make sure it's on your data sheet and in your
notebook.
6.
Now move the first rod to
where the far rod was and put the far rod as far as you can away. (Remember the
keep them straight up!) Line the horizon and far rod's top up again, measure
and record it and do the same thing over and over until you get to the
water.
7.
Now that it is all in
your notebook and data sheet, pick up everything except the metal pole. You
want to keep that there to mark where you were the next time you come.
8.
While you're getting
everything, if there's any trash try to pick all of it up. We we to keep the
beaches nice and clean.
9.
Make some observation
while you're there also, like if you saw any animals or the sea was at high
tide.
Great, now can go back to your van/car.
-Sam :-)
Beach Profiling
By: Louisa L.
Materials:
Emory rods
Hammer
Metal pole also known axed point
Camera
Metal detector
G.P.S device
Data collector sheet
Pencil
More than one person (three people is acceptable)
Clear horizon
Beach
A device that finds the horizon
Methods:
1. Find the longitude and latitude of the beach.
2. Find the axed line. (also known as a metal pole)
3. Always make sure that your Emory rods are lined up,
now you can start!
4. Start at the axed line and work from there with your
Emory rods.
5. Line up the emory rods with the horizon and start the
process of beach profiling.
6. Do this until you get to the waters edge and remember
to write down all your data on the data collector sheet.
7. Remember when you leave to pick up all the litter you
left behind if you did. It is also great when you pick up garbage that was
there before hand.
Thing to know
* You will need to know what a plumb line is.
A plumb line is a small weight, almost like a fishing line that will tell you
if the emory rods are even.
Beach profiling By Jake T.
Materials
·
Visible horizon
·
Emory Rods
·
GPS Device
·
Hammer
·
2 poles
·
Camera
·
Metal Detector
·
Pencil
·
Data collection sheet
·
At least 2 people
Methods
- Create
or find a starting and hammer one pole there.
- Find
the wrack line and hammer the other pole there.
- Find
the longitude and latitude.
- Line
up the other pole with the one hammered in on the wrack line.
- Take
the Emory rods and line them up with the pole on the wrack line. Make sure
the rope is taught.
- Then
the person holding the rod closest to the dunes has to line up the top of
the other rod with the horizon and see where it appears on the rod closest
to the dune.
- Right
the measurement down on the data collection sheet.
- Move
the rod closest to the dunes right next to the other rod and then stretch
out that rod as far as it can go to the wrack line. Be careful and check
if you are still going straight!
- Repeat
steps 1-7 until you get to the pole on the shoreline. After that you have
accomplished Beach Profiling!!!!
Beach profiling by Anah B.
Procedure:
Materials:
·
emory rods
·
hammer
·
2 metal poles
·
camera
·
metal detector
·
GPS
·
pencil
·
3 partners (at least)
·
collection sheet
·
visible horizon
Methods:
- Place
1 of the metal poles in the ground where the dune starts. Use the hammer
to pound on the top of the pole to push it farther into the ground.
- Hammer
the second pole into the ground where the waves break.
- Take
longitude and latitude with the GPS.
- Line
the first emory rod up with the pole at the start of the dunes. Take the
second emory rod and line it up with the horizon. The farthest one from
the horizon should be right in front of the pole on the horizon.
Make sure that the rope between the two emory rods is tight.
- Line
up the top of the emory rod that is closest to the horizon, with the
horizon. Then see where that line lands on the numbers on the emory rod
that is farthest away from the horizon
- Write
down the answer in the collection sheet.
- Keep
repeating steps 4, 5 and 6 until you reach the second metal pole where the
waves break.
- When
you leave the beach, leave it better than when you found it.
Beach Profiling by Sophie G.
Procedure:
Materials:
notebook
pencil
emory rods
GPS device
hammer
camera
metal pole (2) (fixed
point)
at least 3 people
laser level
Methods:
Find a beach you would
like to profile.
When you reach the place
on the beach that you want to be your starting point, find the longitude and
latitude so you can come back next season.
Hammer in a pole on the
wrack line. (Where the beach grass ends.)This will be your fixed point.
Line up another pole where
the waves break (Make sure it is lined up with your fixed point.)
Line up one of your emory
rods against your fixed point.The other emory rod should be at a distance so
that the line connecting them is taught.(They should be at a right angle to the
horizon.)
Have person #1 hold the
emory rod that is against the fixed point. Have person #2 hold the emory rod
that is closest to the horizon. Have person #3 take notes and pictures of the
numbers while person #1 and #2 profile the beach.
Then have person #1 find
the horizon and line it up with the top of person #2’s emory rod. Then see
where that invisible line, lines up on the numbers on their emory rod. Collect
the data and tell person #3 so they can record it.(If the horizon isn’t visible,
use a laser level could be helpful.)
Repeat step 7 all the way
down the beach until you get to the pole where the water breaks.
You can see how much the
tide went up since you started.
Clean up after yourself.
Do not leave trash behind!!!
The Joy of Beach Profiling by Samir B.
Materials:
a) Emory
Rods.
b) GPS.
c) Metal
Pole (2).
d) Camera.
e) More
than 2 People.
f) Beach
(The obvious).
g) Visible
Horizon.
h) Note
book.
i) Hammer.
j) Data
Sheet.
Method:
I.
I. Hammer a Metal Pole as your control
point on the rack line (Where the last line of seaweed stops).
II.
II. Using the GPS find the location of your
control point, so you can come back again and Profile the beach every four
season.
III.
III. Place another metal pole at the
swash zone to make a transect line.
IV.
IV. Stand
in front of one Emory rod (Rod 1)
V.
V. Stretch
out the rod 2 as far away as you can *make sure it’s straight*, and tight*
VI.
VI. Standing
in front of rod 1 focus on rod 2 level to level with the horizon.
VII.
VII. Looking
straight forward focus on rod 1 find where the rod 2 and the horizon level up
together.
VIII.
VIII. Record the data on the data sheet.
IX.
IX. Repeat
the steps from IV to VIII.
X.
X. Clean
the beach and yourself, make the beach look better than when you came.
Beach Profiling by Isobel C.
Procedure
A.
Materials
·
Emory rods
·
G.P.S.
·
Hammer
·
Camera
·
Medal pole (2)
·
Medal detector
·
More than one person (3
is good)
·
Pencil
·
Beach
·
Visible horizon
·
Data sheet
B. Methods
- Drive
out to a beach.
- Hammer
a pole into the wrack line (fixed point).
- Find
longitude and latitude from your fixed point so you can come back again.
- Put
the other pole at the water straight across from you.
- Stretch
out the emory rods and put one at your fixed point.
- Record
all of your data using the data sheet.
- Use
positive when there is an incline and use negative when there is a
decline.
- When
you are all done clean up after yourself.
OBSERVATIONS:
When we went we observed that there was one incline (+0.1) and
everything else were negative numbers.
We saw an Osprey fly off with a fish.
We also saw college students who were going to collect plankton
and who were going to do beach profiling as well.
- Isobel
Beach Profiling Katie G.
Materials:
·
GPS
·
Hammer
·
Camera
·
Emory Rods
·
Metal pole
·
Metal Detector
·
Notebook and Pencil
·
More than one person
·
A beach
·
A visible horizon
·
Data sheet
Methods:
- Find
the longitude and Latitude of your location.
- Use
a pole to mark your location by hammering it into the edge of the shore
line.
- Begin
to line up your emory rods across from the pole.
- Make
sure that both poles are straight up and down.
- Have
the person farthest from the ocean line the top of his/ her partners
rod up with the horizon. Then line the numbers on your rod to the top of
your partners rod.
- Once
you find your calculations, record them in your journal.
- Do
this again while moving closer to the ocean.
- To
get closer to the ocean, you will need to have the person farthest from
the ocean take his/her partners spot while having the person closest to
the ocean ( the partner) walk backwords ( towards the ocean) to straighten
both rods again.
- Do
these steps over and over till you have reached the water surface.
- Keep
the pole in the ground until you come back the next season.
- Come
back each season to see how the beach had eroded over time.
- Once
you are done beach profiling, you might want to pick some trash
up that you see along the beach to keep our planet clean.
Beach Profiling Alden T,
M͟a͟t͟e͟r͟i͟a͟l͟s͟:
- ᴇᴍᴏʀʏ ʀᴏᴅs
- ᴄᴀᴍᴇʀᴀ
- ʜᴀᴍᴍᴇʀ
- ᴍᴇᴛᴀʟ ᴘᴏʟᴇs (2)
- ᴍᴇᴛᴀʟ ᴅᴇᴛᴇᴄᴛᴏʀ
- ɢᴘs
- ᴘᴇɴᴄɪʟ/ ᴅᴀᴛᴀ
ᴄᴏʟʟᴇᴄᴛᴏʀ
- ɢʀᴏᴜᴘ/ ᴘᴀʀᴛɴᴇʀ
- ʙᴇᴀᴄʜ
- ᴀ ᴛʜɪɴɢʏ ᴍᴏʙᴏʙᴇʀ
M͟e͟t͟h͟o͟d͟s͟:
1. ғɪɴᴅ ᴏʀ ᴄʀᴇᴀᴛᴇ ᴡʀᴀᴄᴋ
ᴘᴏɪɴᴛ.
2. ʜᴀᴍᴍᴇʀ ᴏɴᴇ ᴏғ
ᴛʜᴇ ᴍᴇᴛᴀʟ ᴘᴏʟᴇs ɪɴᴛᴏ ᴛʜᴇ ɢʀᴏᴜɴᴅ ᴀᴛ ᴛʜᴇ ᴡʀᴀᴄᴋ ᴘᴏɪɴᴛ.
3. ɢᴇᴛ ɢᴘs ᴄᴏᴏʀᴅɪɴᴀᴛᴇs.
4. ʟɪɴᴇ ᴜᴘ ʏᴏᴜʀ sᴇᴄᴏɴᴅ
ᴘᴏʟᴇ ᴡɪᴛʜ ᴛʜᴇ ғɪʀsᴛ ᴏɴᴇ ʙᴜᴛ ᴏɴ ᴛʜᴇ ᴡᴀᴛᴇʀs ᴇᴅɢᴇ.
5. ʟɪɴᴇ ᴜᴘ ʏᴏᴜʀ ғɪʀsᴛ
ᴇᴍᴏʀʏ ʀᴏᴅ ᴡɪᴛʜ ᴛʜᴇ ᴏɴᴇ ғᴀʀᴛʜᴇsᴛ ᴀᴡᴀʏ ғʀᴏᴍ ᴛʜᴇ ᴡᴀᴛᴇʀ.
6. ʀᴇᴘᴇᴀᴛ sᴛᴇᴘ 5 ᴜɴᴛɪʟ
ʏᴏᴜ ʀᴇᴀᴄʜ ᴛʜᴇ ᴘᴏʟᴇ ᴅᴏᴡɴ (ᴏʀ ᴜᴘ) ɴᴇᴀʀ ᴛʜᴇ ᴏᴄᴇᴀɴs ᴇᴅɢᴇ.
7. ᴜsɪɴɢ ᴀ ᴘᴇɴᴄɪʟ, ʀᴇᴄᴏʀᴅ
ᴅᴀᴛᴀ ɪɴ sʜᴇᴇᴛ.
8. ᴄʟᴇᴀɴ ᴛʜᴇ ʙᴇᴀᴄʜ. ʟᴇᴀᴠᴇ
ɪᴛ ɴɪᴄᴇʀ ᴛʜᴀɴ ᴡʜᴇɴ ʏᴏᴜ ғᴏᴜɴᴅ ɪᴛ.
sᴏʀʀʏ ᴀʙᴏᴜᴛ ᴛʜᴇ 2 ᴘᴀʀᴛs.
ɪ ᴀᴄᴄɪᴅᴇɴᴛᴀʟʟʏ ʜɪᴛ sᴇɴᴅ ᴡʜᴇɴ ɪ ғɪɴɪsʜᴇᴅ ᴛʜᴇ ᴡᴀᴛᴇʀ ᴍᴀᴛᴇʀɪᴀʟs... ᴡʜᴏᴏᴘsɪᴇs....
- ᴀʟᴅᴇɴ
Beach
profiling by JohnCarl M.
Materials
Emory rods
Hammer
Camera
Metal poles (2)
Beach
Either horizon or horizon
finder
Two or more people
GPS
Data table
pencil or pen or other
writing material ( you know like chalk or, coal although I don't recommend it)
Journal
Methods
Step 1. Go two the wrack
line (the wrack line is where the seaweed and other debris are deposited) make
sure it’s the top one. Hammer in one of the poles there and line up one Emory
rod with that metal rod.
Step 4. Take the
longitude and latitude of the metal pole using the GPS.
Step 3. Hammer in one
pole down by the water so as its lined up with the Emory rod and the other
metal rod.
Step 4. Line up your
other Emory rod with all the other rods Emory or otherwise.
Step 5. Lean down by the
Emory rod farther up beach and line the top of the other Emory rod up with the
horizon.
Step 6. Trace that line
across to your pole to see how far that stretch of land goes down.
Step 7 if that doesn't
match up that's because the beach goes up. In that case line up your pole
up with the horizon and trace it over to the other pole to see how far it goes
up.
Step 8. Record your
results in a data table
Step 9. Repeat steps 6
and\or 7 and 8 until you reach the ocean.
Step 10. Record
interesting facts in your journal.
How To Properly Beach
Profile
By Elena M. Tittel
4/15/15
4:18pm
61˚degrees
Before I talk about how to profile a beach, I would like
to briefly talk about the field trip I went on with Lenny and Matt
last week.
We first took a walk around, and looked at the trees, or pollen
trees, or as someone said Broccoli Trees. Also, we learned about Bud
Burst!
Then, we headed to the beach. It was beautiful and sunny, and I
had a lot of fun!
Now, here is how you properly profile a beach!
Before you start, make sure you have the following things:
•Emory Rods
•A metal pole
•GPS Device
•Hammer
•Camera
•Metal Detector
•People to work with (Preferably at least 2)
•A Pencil
•A notebook
•A beach (obviously)
•Horizon
•Data Sheet
•Binoculars
•A Beach Profile Survey
Once you have made sure you have everything you need,
follow these simple steps and you'll be an expert on Beach Profiling in no
time!
Step 1: First things first, you must find the rack line, which
is where you'll be looking to measure the beach.
Step 2: Now, using your hammer, hammer in the metal pole into
the beach.
Step 3: Next, get your GPS location, using your GPS device.
Step 4: Then record the latitude and longitude, the
time, and weather.
Step 5: Take your Emory Rod, and get the other people to line up
the other rod with the horizon.
Step 6: Once you have done that, make sure the rods are
lined up, and then using whats called a plum line, record the data point by
point.
Step 7: Before you record your data on the data sheet, clean
up after yourself, and make sure there is no trash, or belongs on the
beach.
Step 8: Finally, record your data on the data sheet, and pack up
your stuff.
That is how you profile a beach!
~Elena
No comments:
Post a Comment